Innovative solutions for creating healthy, efficient, eco-friendly homes

Roofers Butte MT

Roof leaking repairs can’t be ignored. Weathering, wind damage and improper roof design may cause problems that need to be fixed right away. Here you will learn what to do about leaking roofs, as well as get access to the experienced roofing contractors in Butte, MT listed below that can take care of any problems including emergency roof repairs.

Bradford Roof Management
(406) 252-2278
501 Bernard Street
Billings, MT

Data Provided by:
Alan Hall Roofing
(406) 590-8722
910 6Th Avenue North
Great Falls, MT

Data Provided by:
Infinity Roofing & Siding
(406) 600-1567
1518 W. Beall
Bozeman, MT
Services
Roofing,Siding,Gutters and Windows
Awards
BBB
Hours
24 Hours
Membership Organizations
NRCA

Harmon Enterprises
(406) 209-6073
7260 Meadow View Road
Manhattan, MT
 
PAK Roofing & Remodel
(406) 209-3004
10 Meagher Ave.
Bozeman, MT
 
Premier Exteriors
(406) 591-0885
284 Westchester Square N. Ste B
Billings, MT

Data Provided by:
Kelley's Rain Gutters
(406) 721-1982
435 N 3RD St W
Missoula, MT

Data Provided by:
R & R Roofing
(406) 661-3771
4038 Pine Cove Road
Billings, MT
Services
Roofing Contractor, Roof Repair, Roofers, Roofing Service, Roofing Company
Hours
Mon-Fri 8am-5pm

Epperson Enterprises, Inc.
(406) 563-2385
617 Elm
Anaconda, MT
 
Auchly Roofing Inc
(636) 332-8200
38 Barnor Road
Wentzville, MT
 
Data Provided by:

Roofing

Provided By:

QUESTION: During a recent trip to my attic, I found evidence that I have a leak in my roof. Can I fix a leaking asphalt roof myself?

ANSWER:With a little time and patience, most roof leaks can be tracked down and patched. The first step is assessing the entire roof before you begin patching. A roof truly in need of re-shingling will thwart most attempts at patch jobs. Typically, asphalt roof shingles at the end of their lives will curl up and/or bubble. Also, the granules on a defunct shingle's surface will be nearly gone, and pieces of shingle or entire shingles will be missing. In a case like that, it's best to re-shingle the entire roof. However, if your roof shingles are in decent shape, remember that roof leaks don't always end in the attic at the spot where they begin on the exterior roof's surface. Sometimes a leak begins 10 or 12 feet from where it ends.

Still, the most notorious locations for roof leaks are around a chimney, in dormer and gable valleys, and in corners where a sloping roof abuts a vertical wall. At the chimney, leaks often originate where the sheets of lead flashing that come out of the chimney meet the roof. These sheets fold down the side of the chimney and are woven under the nearby shingles. In between the individual layers of lead flashing, water often penetrates and works its way under the roof material.

The best solution here is pumping plastic roof cement (a tar-like substance) in between the layers of flashing. Plastic roof cement can be purchased in tubes sized for an ordinary caulking gun, which is the most convenient tool for applying the goop without a lot of mess. In roof valleys, the search for a leak source and the proper fix is a bit trickier. Most valley leaks don't show up until the roof carries a snow load or debris in the valley stacks up deep enough to hold water.

If the leak appears when these conditions are in place, then it's time to tear up at least one set of valley shingles and see what's underneath. At the very least, there should be extra layers of roofing felt under the valley shingles. Better yet, metal flashing or bituminous roofing underlayment should be under the shingles. But most often, there's no extra waterproofing in the valley, and that's why you have the leak in the first place. When replacing small areas of asphalt shingles, try to work during warm (70° F or so) and overcast days. This makes removing the bad shingles easier and results in less damage to the good shingles nearby. Gently roll back the good shingles and remove both the underlying nails and bad shingles as you go, working from the top of the valley down. Remove shingles at least three feet away from the valley. Before installing new shingles, be sure you have proper flashing or the bituminous ice and water shield firmly in the valley.

This same approach is used when leaks are located near the point at which a vertical wall meets a sloping roof. The only difference is some wall siding must be removed to install new flashing or a water shield both on the roof surface and at least 18 inches up the abutting wall.

Click here to read article from Smart-Homeowner.com